Gas furnace replacement in Minnesota’s Twin Cities costs $6,000 to $10,000 or more installed, based on MSP’s 2026 pricing. Most of our customers pay close to $8,000, which covers a standard furnace connected to their existing ductwork. Higher-efficiency equipment, a bigger heat load and extra work on venting, gas lines or ducts push a job toward the top of that range.
Those are planning numbers. A firm price comes after a technician sees your basement, measures your home’s heat loss and checks the venting. Jump to a section:
- What each price level buys
- Furnace size and heat loss
- Efficiency rating (AFUE)
- Installation complexity
- Add-on features
- Rebates and tax credits in 2026
- Repair or replace
- The contractor you hire
What a New Gas Furnace Costs at Each Price Level
These are MSP’s published furnace installation prices for the Twin Cities as of 2026.
| Price level | What it usually covers |
|---|---|
| About $6,000 (starting price) | An entry-level furnace installed in place of the old one, with little or no change to venting or ductwork |
| About $8,000 (most common) | A standard installation: the new furnace plus connection to your existing ductwork |
| $10,000 and up | A high-efficiency furnace with upgrades, such as a variable-speed blower, a modulating gas valve, new venting or duct changes |
When you compare quotes, line them up item by item. Each one should name the furnace model and its AFUE rating, the permit, removal of the old unit, any venting or gas line work, and the warranty. A cheap quote that leaves out venting work tends to grow once the old furnace comes out.
SCHEDULE FREE ESTIMATEFurnace Size and Your Home’s Heat Loss
Furnace capacity is measured in BTUs per hour. A small, well-insulated home might need around 50,000 BTUs. A large or drafty house can need 100,000 or more, and bigger furnaces cost more to buy.
Matching the size of the old furnace is a common mistake. Plenty of older Minnesota homes have had new windows, added insulation or an addition since their last furnace went in, and each of those changes the heat load. Your layout matters too, since a split-level or a finished basement spreads heat differently than a compact two-story.
A Manual J heat loss calculation settles the question. It measures how much heat your house loses on a design-cold day and sizes the furnace to match. An oversized furnace short-cycles, wears out sooner and leaves some rooms colder than others. An undersized one runs nonstop on a -20°F night and still can’t keep up.
Efficiency Rating (AFUE)
AFUE (annual fuel utilization efficiency) tells you how much of the gas you pay for becomes heat in your home. An 80% AFUE furnace turns 80 cents of every gas dollar into heat and sends the other 20 cents up the chimney. Gas furnaces sold today fall into two groups:
- Mid-efficiency (non-condensing), 80% AFUE: vents through a metal flue or chimney and costs less up front.
- High-efficiency (condensing), 90% to 98% AFUE: captures extra heat from the exhaust, vents through PVC pipe and needs a condensate drain.
For most Twin Cities homes, a condensing furnace is the better buy. Our heating season runs long, so the fuel savings add up faster than they would in a milder state, and utility rebates go to high-efficiency models. For the payback math, see our comparisons of 80% vs. 90%+ AFUE furnaces and condensing vs. non-condensing furnaces.
Federal rules point the same way. The U.S. Department of Energy set a 95% AFUE minimum for most new residential gas furnaces, with a compliance date of December 18, 2028. Gas industry groups have challenged that rule in court, so the date could still move. The standard covers furnaces made after that date. It doesn’t require you to replace one that’s already in your home.
Some homeowners also price a cold-climate heat pump or a dual-fuel system that pairs a heat pump with a gas furnace for the coldest nights. Our heat pump cost guide covers that side.
Installation Complexity
Two furnaces with the same price tag can lead to very different quotes once the installer looks at the house. These are the most common reasons a job costs more:
- Access: tight crawl spaces, narrow basement stairs and finished utility rooms add labor.
- Venting: moving from an 80% furnace to a condensing model means new PVC vent pipes through a wall and a condensate drain. It can also leave a gas water heater alone in a chimney sized for two appliances. That “orphaned” water heater may need a chimney liner or its own vent.
- Gas line and electrical: an undersized gas line or a missing circuit for a condensate pump means extra work.
- Ductwork: leaky or undersized ducts can waste the efficiency you paid for and may need sealing or changes.
- Permits: Minneapolis, St. Paul and other Minnesota cities require a mechanical permit to replace a furnace. Your installer should pull it, and a city inspector checks the work afterward.
Add-On Features
Comfort upgrades raise the price, and they also change how the house feels. The three that matter most:
- Blower motor: a single-speed blower runs at full blast. A variable-speed blower adjusts airflow to the heat you need, which runs quieter and evens out temperatures between rooms.
- Gas valve: a single-stage valve is either off or on high. A two-stage valve adds a low setting for mild days, and a modulating valve adjusts in small steps for the steadiest heat.
- Insulated blower cabinet: cuts the noise you hear from the furnace.
Variable-speed blowers and modulating gas valves are what usually move a job into the $10,000-and-up range.
Rebates and Tax Credits for a New Furnace in 2026
The federal tax credit is gone. The Energy Efficient Home Improvement Credit (Section 25C) used to cover up to $600 of a qualifying high-efficiency gas furnace. The One Big Beautiful Bill Act, signed July 4, 2025, ended the credit for equipment placed in service after December 31, 2025. A furnace installed in 2026 doesn’t qualify, so question any quote or article that still subtracts it. The IRS explains the change here.
Utility rebates are still available. CenterPoint Energy and Xcel Energy, the two main gas utilities in the Twin Cities, both run rebate programs for Minnesota customers. Where a gas furnace rebate is offered, it goes to a high-efficiency model installed by a contractor. Amounts and rules change every year, so check your utility’s current terms before you buy. MSP can tell you which rebates your furnace qualifies for and help you file. Our guide to Minnesota HVAC rebates has more detail.
Minnesota’s federally funded home energy rebates (HEAR) cover heat pumps and other electric equipment, not gas furnaces, and the program had not launched as of mid-2026. If you’d rather spread the cost out, MSP also offers financing.
Repair or Replace: How to Decide
Most gas furnaces last 15 to 20 years. Past that age, a major repair often buys only a season or two. MSP’s technicians use a simple test: if the repair costs more than half the price of a new furnace, replace it.
Other signs it’s time to replace:
- The furnace is 15 years old or more and needs a major repair.
- You’ve had repair calls in each of the last two heating seasons.
- A technician found a cracked heat exchanger. That can leak carbon monoxide, and the furnace should stay off until it’s fixed or replaced.
- Your gas bills keep climbing while your rates and habits stay the same.
- Some rooms stay cold, or the furnace turns on and off in short bursts.
Some contractors use a “$5,000 rule” as a quick check: multiply the furnace’s age by the repair quote, and if the result tops $5,000, replace. A 14-year-old furnace with a $400 repair comes out to $5,600, which points to replacement.
A 30-year-old furnace is well past its expected life and far less efficient than anything sold today. Replacing it on your schedule beats replacing it during a January cold snap, when every installer in the metro is booked. Our article on whether to repair or replace your furnace goes deeper.
The Contractor You Hire
The installer affects the price and how long the furnace lasts. A furnace that’s sized wrong or vented poorly can short-cycle, waste gas or fail early, no matter what brand it is.
Before you sign, check that the contractor is bonded with the Minnesota Department of Labor and Industry and licensed in your city, pulls the permit, and runs a heat loss calculation instead of guessing the size. Ask for the furnace model number and AFUE rating in writing.
MSP Plumbing Heating Air has installed furnaces in the Twin Cities since 1918. Our NATE-certified technicians give you an upfront price before any work starts.
Get a Firm Price on Your New Furnace
We’ll measure your home’s heat load, check your venting and ductwork, and give you a written quote for furnace installation. Schedule a free estimate today.
SCHEDULE FREE ESTIMATEFor more on heating and cooling costs, see our guides to timing a furnace or AC purchase and AC replacement costs.

